This page was exported from 2019 Free IT Exam Dumps Collection - Braindump2go [ http://www.hpdumps.com ] Export date:Fri Nov 15 16:23:47 2019 / +0000 GMT ___________________________________________________ Title: [Feb-2017-Updated]Download Braindump2go 644-906 Dumps VCE 80q Free[Q41-Q50] --------------------------------------------------- 2017 Feb. NEW 644-906: Implementing and Maintaining Cisco Technologies Using IOS XR - (IMTXR) Exam Questions Updated Today!Free Instant Download 644-906 Exam Dumps (PDF & VCE) 80Q&As from www.braindump2go.com Today! 100% Real Exam Questions! 100% Exam Pass Guaranteed! 1.|NEW 644-906 Exam Dumps (PDF & VCE) 80Q&As Download:http://www.braindump2go.com/644-906.html 2.|EW 644-906 Exam Questions & Answers Download:https://1drv.ms/f/s!AvI7wzKf6QBjgktwWG6fOotKPwTZ QUESTION 41Which Cisco IOS XR command sequence will load a specific configuration? A.    (config)#load disk0:name.cfgB.    #copy disk0:name.cfg running-confirgurationC.    #copy tftp://255.255.255.255/name.cfgD.    #load commit changes <name>E.    (config)#load commit <name> Answer: A QUESTION 42Which is-is router interface configuration command will configure the authentication password for IS-IS Hello (IIH) messages without actually sending the password with the IIH over the network? A.    hello-password text clear secretkeyB.    hello-password hmac-md5 clear secretkeyC.    hello-password text encrypted secretkeyD.    hello-password hmac-md5 encrypted secretkey Answer: B QUESTION 43What is the correct procedure to associate a VRF to a static route? A.    configure the VRF under the interfaceB.    specify the VRF under "router static" in configuration modeC.    define the VRF in the global configurationD.    specify the VRF in the route global configuration command Answer: B QUESTION 44What is the correct Cisco IOS XR command to configure an autonomous system number 1000 for BGP and to support IPv4, IPv6, and unicast routing? A.    router bgp 1000address-family ipv4 unicast!address-family ipv6 unicast!!B.    router bgp 1000neighbor 1.1.1.1 remote-as 2000address-family ipv4 unicast!address-family ipv6 unicast!!C.    router bgp 1000address-family vpnv4 unicast!address-family vpnv6 unicast!!D.    router bgp 1000neighbor 1.1.1.1 remote-as 2000address-family vpnv4 unicast!address-family vpnv6 unicast!! Answer: A QUESTION 45Which Cisco IOS XR show command is used to display the IPv4 BGP table? A.    show bgpB.    show bgp summaryC.    show bgp neighborsD.    show route bgpE.    show bgp vpnv4F.    show bgp table Answer: A QUESTION 46Which of the following configurations adds a community to routes that are matched on AS criteria? A.    route-policy policy1if as-path in set1 thenset community (356:1000)endifend-policyB.    route-policy policy1if community in set1 thenset community (356:1000) additiveendifend-policyC.    route-policy policy1if as-path in set1 thenset community (356:1000) additiveendifend-policyD.    route-policy policy1if as-path neighbor-is set1 thenset community (356:1000) additiveendifend-policy Answer: C QUESTION 47How would MPLS Label Distribution Protocol, Graceful Restart be configured on TenGigE 0/0/0/1? A.    Interface Ten0/0/0/1mpls ipGraceful-restartB.    router ospfinterface Ten 0/0/0/1address-family ipv4 unimpls ipgraceful-restartC.    mpls ldpaddress-family ipv4 unicastmpls ipgraceful-restartD.    mpls ldpgraceful restartinterface Ten 0/0/0/1 Answer: D QUESTION 48Which three commands can verify that the route-policy shown below and applied inbound on the BGP neighbor is working as expected for prefix 2.0.0.0/8? (Choose three.) A.    show bgp 2.0.0.0 | include 356:1000B.    show bgp | include 2.0.0.0C.    show bgp community 356:1000 | include 2.0.0.0D.    show bgp 2.0.0.0 Answer: ACD QUESTION 49Refer to the exhibit. Based on the configuration, which two statements are true for RTR1? (Choose two.) A.    SNMP traps that are going out on TenGigE 0/0/0/0 will be dropped.B.    SNMP polling that is coming through interface TenGigE 0/0/0/0 will be dropped.C.    The Telnet connection that is coming through MgmtEth0/RSP0/CPU0/0 will be dropped.D.    TACACS traffic that is originating from RTR1 and going through TenGigE 0/0/0/0 will be dropped.E.    The SSH connection that is coming through TenGigE 0/0/0/0 from host 5.5.5.5 will be accepted. Answer: BE QUESTION 50Which command will show the IP address of a Cisco Discovery Protocol neighbor? A.    show cdpB.    show cdp entryC.    show cdp interfaceD.    show cdp neighbors Answer: B !!!RECOMMEND!!!   1.|NEW 644-906 Exam Dumps (PDF & VCE) 80Q&As Download:http://www.braindump2go.com/644-906.html 2.|EW 644-906 Study Guide Video: YouTube Video: YouTube.com/watch?v=7U0WVbIpck0 --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2017-02-18 03:44:01 Post date GMT: 2017-02-18 03:44:01 Post modified date: 2017-02-18 03:44:01 Post modified date GMT: 2017-02-18 03:44:01 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com